KWI Clutching

5 products
Quick view
WSRD/KWI Ultimate Primary Bolt | 2017+ X3 Models
KWI Clutching
$75.00
Quick view
WSRD/KWI Can-AM X3 Thermostat Delete Kit | 2017-2019
KWI Clutching
$44.00
Quick view
RE-ENFORCER for Can-Am X3
KWI Clutching
$499.00
Quick view
X3 Float Mod
KWI Clutching
from $257.00
Quick view
KWI X3 Race Helix
KWI Clutching
$226.00
KWI Clutching

WSRD/KWI Ultimate Primary Bolt | 2017+ X3 Models

$75.00 Save $-75.00
Introducing a solution for a very dangerous problem; the 630  "Ultimate" Primary Clutch Bolt for all 2017+ Can-Am X3 models.
The Ultimate Bolt directly replaces the OEM Can-Am X3 primary clutch bolt and uses the stock bellville washer. This bolt works with the OEM clutches, aftermarket clutches, and available billet clutches (STM non-DR clutches) that utilize the stock OEM length primary bolt.
What's included? 
  • WSRD/KWI Ultimate Primary Bolt
  • Installation lubrication
  • Install instructions and torque specifications
Stock primary clutch bolts can break under elevated stress as well as extended torque cycles allowing the clutch/crankshaft/governor cup taper to uncouple causing costly damages to the clutches, crankshaft, housing, and other components in the clutching area! The Ultimate Clutch Bolt was developed to eliminate this problem. The 630 "Ultimate" Bolt is made from ultra strong 200,000 PSI material that provides a massive improvement in clutch bolt strength and clutch/crankshaft taper stability as well as holding power. 

WSRD tested the Ultimate Bolt using a bolt tension pressure tool to compare against the OEM bolt in the video below.



WSRD/KWI Ultimate Primary Bolt | 2017+ X3 Models
KWI Clutching

WSRD/KWI Can-AM X3 Thermostat Delete Kit | 2017-2019

$44.00 Save $-44.00
Whalen's Speed Research and Development & KWI have partnered on this affordable and simple cooling solution for those of you who race or push your Can-Am X3 to the limit with big HP. By installing the WSRD/KWI Thermostat Delete Kit you will get maximum coolant flow to control the heat developed by extreme conditions and high boost levels. Tested and developed under the harshest race and recreational conditions we have seen excellent results by performing this simple modification.
In this video, we will show you how to install the KWI x WSRD Thermostat Delete Kit.
WSRD/KWI Can-AM X3 Thermostat Delete Kit | 2017-2019
KWI Clutching

RE-ENFORCER for Can-Am X3

$499.00 Save $-499.00

Strengthen, stabilize, and support your clutch shafts to increase wheel HP, prevent belt misalignment due to shaft flex, prevent taper uncoupling on high HP motors!  Includes integrated belt changing tool- simply uses the OEM torx bolt to remove the belt.

When your clutches shift under acceleration the belt pulls the 2 clutches together with extreme forces bending the gearbox input shaft and crankshaft because they are only supported on one side. This bending causes clutch misalignment; belt slip; belt heat; wheel HP loss; and on high HP engines this flex will cause bolt breakage; primary clutch taper uncoupling and severe damage. The KWI RE-ENFORCER fixes all these issues by supporting the opposite side of the shafts. Works with the KWI Float Mod and OEM non-floated Can-Am X3 clutches.  Made with the highest grade materials, lightweight, and ultra-strong. 7075 aluminum, Chromoly Heim joints, and ceramic bearings rated for 11000 RPM.

*Not compatible with OEM Variator Cover (Clutch cover)**Clutch cover must be removed**

PARTS INCLUDED

2 each-  Bearing Housing

1 each-  Primary Brace Cup

1 each-  Primary Brace Retaining Washer

1 each-  KWI 630L ULTIMATE clutch bolt and Lubricant

1 each-  Brace secondary clutch bolt

1 each- Secondary Brace Spacer

1 each- Secondary Brace retaining washer

2 Each- Brace Rods with Rod ends #15 and Jam Nuts #16

4 Each- Brace rod bolt washers

4 Each- Brace rod bolts

**RACING IS A DANGEROUS ACTIVITY AND PURCHASERS OF KWI CLUTCHING PRODUCTS ACKNOWLEDGE THE INHERENT RISKS ASSOCIATED. KWI CLUTCHING MAKES NO REPRESENTATIONS THAT ITS PRODUCTS CAN REDUCE OR ELIMINATE ANY SUCH RISK. KWI CLUTCHING products are NOT FOR STREET, HIGHWAY, OR AIRCRAFT USE and are intended ONLY for race vehicles operated on closed-course facilities or race tracks with appropriate supervision of qualified technicians or mechanics to ensure that the safety needs of the race driver and others are met. KWI CLUTCHING products could be combined with other products or parts which may not be suitable and could adversely affect the performance of other race parts or the vehicle. The user shall determine the ultimate suitability and safety of the product for its intended use, and the user assumes all responsibility and risk in connection therewith.**

RE-ENFORCER for Can-Am X3
RE-ENFORCER for Can-Am X3
RE-ENFORCER for Can-Am X3
RE-ENFORCER for Can-Am X3
RE-ENFORCER for Can-Am X3
RE-ENFORCER for Can-Am X3
KWI Clutching

X3 Float Mod

$1,522.00 Save $-1,522.00

KWI FLOAT MODIFICATION BENEFITS:

  • Fix warped clutch sheaves (All of the X3 clutches are warped, and most are warped more than .010" causing belt chatter, loss in wheel HP and increased belt heat.)

  • Fix factory belt misalignment (The secondary clutch is locked in place by BRP to ensure smooth shifting at idle, however; this causes clutch and belt misalignment during shift out, robbing wheel HP and creating belt heat)

  • Lowers belt temps (KWI will resurface and recut your sheave angles for more efficient shifting and more wheel HP)

  • Longer belt life (More efficient power transfer thru the CVT clutch system means less heat and stress which prolongs belt life)

  • Quicker acceleration over unmodified clutches (Testing shows over 1/2 car lead by 60mph over stock unmodified clutches)

  • Quieter clutches (by eliminating warping and belt chatter your clutches will run quieter)

KWI has a proven fix used by thousands of X3 owners worldwide that not only will increase your wheel HP but stabilizes your belt temps and keep shifting ultra-smooth. KWI will true up your warped sheaves, re-cut the sheave angles on both your primary and secondary clutches, set up your clutches to fully float and self-align at all RPM's, service your primary bearing, replace all wearable and damaged parts (wearable or damaged parts replacement is an additional cost) and send your clutches back ready to bolt-on and go. You can purchase our clutch kit at the same time, and we will install it for you during reassembly. 10 day in-house turnaround time.

Additional Info Below

KWIk Tips: we explain why you would want a KWI Float Mod.


SELECT FLOAT MOD NO CLUTCH KIT IF YOU ALREADY HAVE A KWI CLUTCH KIT.

SELECT REPAIR IF YOU ARE SENDING THE CLUTCHES IN FOR REPAIR

 

FLOAT MOD INCLUDES:

-CNC machine all 4 of your clutch sheaves so they’re perfectly true and straight.

-Disassemble and inspect your clutches and advise of any damage Repair if necessary after approval.

-Install WKP upgraded rollers that are MUCH stronger than anything on the market today. (yes we've tested them all)

-CNC machine your helix with our Race Helix angles.

-If you want a clutch kit we will install and set it up for your tune, terrain, tire size, and riding altitude.

-Clean, service and reassemble your clutch so it’s ready to bolt-on and go. 

-Includes the KWI float spring, spacer, shims, and complete instructions. 

FLOAT MOD UPDATE:

If you already have the KWI float mod and it was done before May 2019 then there’s been great improvements since your clutches last visited us. Select this and we will:

-Re-machine your clutch and modify it to the latest KWI specs.

-Install WKP upgraded rollers that are MUCH stronger than anything on the market today. (yes we've tested them all)

-CNC machine your helix with our Race Helix angles.

-Test and replace your spring if it’s lost some pressure.

-Reassemble your clutch so it’s ready to bolt-on and go.

 

SEND A COPY OF THE ORDER IN WITH YOUR CLUTCHES AND COMPLETELY FILLED OUT THE FLOAT FORM. SEND US YOUR CLUTCHES, AND WE WILL GIVE YOU SUBSTANTIALLY LOWER BELT TEMPS, LONGER BELT LIFE, QUIETER AND SMOOTHER OPERATING CLUTCHES, AND MORE WHEEL HP! WE WILL ALSO MACHINE YOUR WARPED CLUTCH SHEAVES, SO THEY’RE PERFECTLY STRAIGHT. MODIFY YOUR CLUTCHES WITH OUR PATENTED FLOAT MODIFICATION TO CORRECT THE FACTORY CLUTCH MISALIGNMENT; RECUT YOUR FACTORY HELIX WITH OUR SPECIAL CNC RACE ANGLES TO GIVE YOU MUCH STRONGER MID-RANGE AND TOP-END POWER. INSTALL WKP CAN-AM MAVERICK X3 HD SECONDARY CLUTCH ROLLERS TO REPLACE THE BRITTLE FACTORY ROLLERS, INSTALL A CLUTCH KIT SPECIFICALLY DESIGNED FOR YOUR TUNE, TERRAIN, AND ALTITUDE.   ***DOES NOT INCLUDE ANY OVER AND ABOVE REPAIR PARTS OR LABOR OR SHIPPING; THESE ITEMS WILL BE PROCESSED PRIOR TO SHIPPING YOUR CLUTCHES BACK****

 

-X3 MODEL OUTER HALF UPDATE

All model years of 120HP version, all 2107 models and all early production 2018 Can-AM X3 models came with a primary clutch outer half design that was a thinner, all-aluminum casting and suffers from accelerated tower wear at the slider shoe contact surface, especially in higher HP units (over 120HP). This older design was also noisy.  If constant maintenance is not performed to monitor the wear and replace components as necessary then you will end up with a damaged outer half and governor cup which will cost approx $700 to replace. To prevent this accelerated wear and damage we suggest you send your clutches into us to have the outer half replaced with the new design that is much more robust, has steel wear plates, will not wear like the older models and is much quieter.

 

FREE T-STIRT or HAT with every float mod





X3 Float Mod
KWI Clutching

KWI X3 Race Helix

$226.00 Save $-226.00
X3 Race helix - We will supply you with a NEW BRP X3 helix with our special RACE angle that increases mid-range acceleration, increases top speed, improves back shifting and lowers belt temps. We have developed this helix angle through hundreds of hours of testing in the harshest conditions to be the best possible performing angle for your X3.
KWI X3 Race Helix